Portable Appliance Testing

·          Did you know your insurance could be invalidated if you have not carried out testing of your portable appliances?

·          Did you know that you are liable by law for the safety of your electrical equipment?

·          Did you know you can fail a fire inspection by not having your portable appliances tested?

·          Did you know you require a record of portable appliance testing for your Health & Safety file?

 

Our portable appliance testing is carried out at a time to suit you, it is completed with ‘minimal intrusion’ in mind and also combining speed with thoroughness so that you have as little disruption to your working day as possible.  We will discuss the best routes to take for testing and you will find our testers to be professional, well presented and polite.

Every portable appliance tested by Property One is visually inspected to check the plug, flex and body of the appliance. In this visual inspection we will investigate for damaged equipment, frayed flex cords and/or flex cords taped up to cover unauthorised joints, flex wiring pulled away and exposed from the internal casing of the plug, signs of overheating on the flex and internal wiring inside the plug, cracked and damaged plugs including loose and faulty wiring connections inside the plug.

A high number of appliances fail this visual inspection due to having the wrong type of fuse in the plug, loose plug connections, exposed wiring at the plug and damaged plugs.

As part of our service, minor repairs such as above will be repaired free of charge, thus allowing the appliance to pass the visual inspection.

Testing Procedure
Only when we are satisfied that the equipment has passed the visual inspection, a series of tests using the latest state-of-the-art computer testing equipment are carried out to detect hidden faults and potential hazards. This ensures the electrical safety and good working order of each item.

Computerised and industry set tests are carried out using Portable Appliance Testing equipment similar to the tester pictured above. In the testing procedure we will carry out the following tests.

• Earth Bond Test - Tests the metal casing of equipment to confirm the integrity of the appliance earth conductor. A high A.C. current of  10amp or 25amp is passed between the earth bond terminal and the appliance's earth pin.

• Earth Continuity Test - When testing IT Equipment - e.g. computers in offices, it is undesirable to use the high current Earth Bond Test described above as this could damage the equipment. On IT equipment our testing procedure would involve testing the equipment with a low current earth continuity test. A low current (200 mA D.C.)  is passed between the continuity terminal on the testing equipment and the appliance's test socket earth pin.

• Insulation Test - An insulation test is carried out on all equipment to verify that the insulation resistance is correct and sufficient between the appliance wiring and internal components. In this test a 500 volt D.C. supply is used to test the insulation resistance.

• Operation Test - This test will start up the equipment being tested as if it were normally plugged into a 13 amp socket outlet. By doing this test we will be verifying the power consumed by the appliance, which we will check against the manufacturers rating which is stamped on the appliance. This will also determine if the correct size of fuse is inserted in the plug top.

• Earth Leakage Test - By carrying out the Operation Test we will also find out if any electrical current is flowing to earth. Normally appliances should have no or very little earth leakage current. The appliance tester will also be able to detect earth leakage in Class 2 (Double Insulated) appliances. This enable account to be taken of all leakage paths to earth rather than just that flowing in the earth wire if applicable - e.g. a Class 2 appliance could exhibit earth leakage through its mountings or by operator contact.

• Flash Test - This test ( Dielectric Strength Test) is very rarely carried out and it is not normally carried out as routine test. The test stresses the asset insulation. This test is usually only carried out if the appliance has been completely overhauled and is being put back into working service.

Both visual inspections and instrument tests are carried out in accordance with guidelines and testing procedures laid down by the IEE Code of Practice for Inspecting and Testing of Electrical Equipment.

   

Following testing, each appliance will be labelled “PASS” or “FAIL” and we will provide you with a detailed computer-produced electrical test certificate and a full register of your appliances. These may be used for your own and for your insurer’s records.

Our rates are extremely competitive and large discounts are available for high volume testing - we recommend you contact with your requirements for a personalised quote.